Kelvinforge
Kelvinforge Crossbar Doorway Pull-Up Bar
Stainless steel doorway bar for upper body pulling work
£69£49
- 1 adjustable stainless steel bar, 2 foam grip sleeves, 2 door frame brackets, 1 fitting guide
- ✓ Brushed stainless steel bar fitted between standard door frames
- ✓ Foam grip sleeves for a steady hold during pulling sets
- ✓ No-drill setup with adjustable width brackets
Kelvinforge Crossbar Doorway Pull-Up Bar
Pick the number of bars you need
Express 1-Click Order (Name + Phone)
Selected Package: 2 bars (£59)
Returns within 30 days
You may return the product within 30 days of delivery, under the conditions of our Returns Policy. Contact our support desk to arrange it.
Lewis Carrow
A doorway bar needs even bracket pressure more than anything else. The wide-plate design here holds a steadier fit than the narrow brackets I usually see.
About the Crossbar Doorway Pull-Up Bar
A doorway bar only works as well as the bracket pressing against the frame, since the bar itself rarely bends under normal use. The Crossbar bar is machined from stainless steel hardware and paired with wide door frame brackets that spread the load evenly across the frame rather than pressing in at narrow points, which is usually where cheaper bars start to mark the paintwork or slip under load. The grip area is wrapped in high-density foam sleeves, giving a steady, cushioned hold across wide-grip, narrow-grip or neutral-grip pulling positions. The bar adjusts to fit most standard doorway widths and sets up without any drilling, so it can move between rooms or come down entirely when the doorway is needed clear.
- ✓ Brushed stainless steel resistant to surface corrosion
- ✓ High-density foam grips with no latex contact points
- ✓ Wide-plate brackets reduce point pressure on door frames
How to fit and use the bar correctly
Check both brackets are still pressed firmly against the frame before hanging full bodyweight from the bar.
Loosen the width adjuster slightly if removing the bar between sessions to reduce constant pressure on the frame.
Position the bar at a height that lets your feet clear the floor fully during a hang, which keeps the pulling motion unobstructed.
What fitting and using the bar looks like at first
First fitting
You measure your doorway, adjust the bar width, and test bracket tension with partial bodyweight.
Settling in
You get used to checking tension before sessions and find your preferred hanging height.
Routine use
Fitting and removing the bar between sessions becomes a quick, familiar step.
Kelvinforge bracket design versus a narrow basic bar
Why basic doorway bars slip or mark frames
Narrow contact points concentrate pressure into a small area of the door frame, which can mark paintwork or shift slightly under load over time.
What Kelvinforge changes
Wide-plate stainless steel brackets spread the same pressure across a larger surface, holding a steadier fit without concentrating force on one spot.
How the Crossbar fits and holds in place
Measure the doorway
Confirm your frame width falls within the bar's adjustable range before fitting.
Set the width
Turn the screw-lock adjuster until both brackets reach the frame on either side.
Test the hold
Apply partial body weight first to confirm the brackets are seated firmly.
Begin pulling
Use the foam grip sleeves for wide, narrow or neutral grip positions during your set.
How the bar is packed
The bar ships disassembled into a flat branded box with foam sleeves and brackets separated by card dividers to prevent scuffing in transit.
What people say about this bar
"Fitted it in a few minutes without any tools. The wide brackets haven't marked my door frame at all so far."
Jordan P
Customer
"Solid bar and the foam grips are comfortable. Had to adjust the width screw a couple of times to get it fully snug."
Alicia M
Customer
"Takes seconds to pop in and out when I need the doorway clear. Feels sturdy when hanging full weight."
Sam D
Customer
Frequently asked questions
Will this fit any doorway? +
The bar adjusts across a 68 to 80 cm range, which covers most standard interior doorway widths; measure your frame before ordering if it falls outside this range.
Does it damage the door frame? +
The wide-plate brackets spread pressure across the frame surface rather than a narrow point, reducing marking under normal fitted use, though checking the frame condition periodically is good practice.
Do I need tools to install it? +
No drilling or tools are required, the screw-lock width adjuster is turned by hand to press the brackets firmly against the frame.
Can it be removed and refitted easily? +
Yes, the bar is designed to come down and go back up without needing to reset the bracket positions each time.