Kelvinforge
Kelvinforge CrossBeam Doorway Bar
No-screw doorway pull-up bar built from forged stainless steel
£69£49
- 1 doorway pull-up bar frame, 2 foam grip sleeves, 4 stainless steel mounting brackets, 1 cotton webbing door frame protector set
- ✓ Stainless steel frame fits most standard door frames
- ✓ Foam grip sleeves at both ends for a stable hold
- ✓ Cotton webbing protector guards the door frame finish
Kelvinforge CrossBeam Doorway Bar
Select the CrossBeam package for your setup
Express 1-Click Order (Name + Phone)
Selected Package: 2 bars (£89)
Returns within 30 days
You may return the product within 30 days of delivery, under the conditions of our Returns Policy. Contact our support desk to arrange it.
Richard Oyelaran
The thing I check on any doorway bar is whether it shifts under a dead hang. A four-point mount that stays still lets people focus on their grip and shoulders instead of the frame underneath them.
About the CrossBeam Doorway Bar
The CrossBeam frame is machined from stainless steel hardware tubing, then fitted with four mounting brackets that distribute load across the door frame rather than concentrating it at two points. That distribution is what keeps the bar from flexing noticeably under bodyweight, and it is also why installation takes a few extra minutes compared to a single-clamp design. At each end of the bar sits a foam grip sleeve, dense enough to stay firm through long sets rather than compressing into a soft, unstable surface. A cotton webbing protector sits between the brackets and the door frame itself, there to stop the mounting hardware marking the paint or wood finish during fitting and removal. The bar is designed to come down as easily as it goes up, which matters for anyone renting or sharing a space.
- ✓ Frame machined from quality-controlled stainless steel stock
- ✓ Foam grips free from hollow filler cores
- ✓ Cotton protector strips reduce door frame marking
Composition and dimensions of the bar
| Component | Form / Finish | Dimension / Rating | Purpose |
|---|---|---|---|
|
Stainless Steel frame
✓ Bears the load during hanging exercises.
|
Tubular construction | Fits 60-90cm door widths | † |
|
High-Density Foam sleeve
✓ Gives a firm, stable grip surface.
|
Moulded grip sleeve | 15cm length, 2 sleeves | † |
|
Stainless Steel bracket
✓ Distributes load across the door frame.
|
Angled mounting bracket | 4 brackets | † |
What changes as you get used to the bar
Fitting the bar for the first time
You measure the door frame and adjust bracket tension until the fit feels solid.
Installation becomes routine
Mounting and removing the bar takes only a minute once the positions are known.
Confident repeated use
The bar goes up and comes down as part of a normal session without extra checking.
CrossBeam construction versus single-clamp bars
Why single-clamp bars feel shaky
A bar that grips a door frame at only two points concentrates the full bodyweight load on those spots, which is often why a cheap bar flexes or shifts slightly during use. That movement is unsettling even when the bar technically holds.
What four-point mounting changes
Spreading the load across four brackets reduces the pressure at any single contact point, which is why the CrossBeam frame stays steady through a full hanging position. The protector strips also mean the frame can be refitted repeatedly without new marks appearing each time.
How the four-point mounting holds the bar in place
Measure the frame
Confirm the door width falls within the bar's adjustable range before fitting.
Position the brackets
Set all four brackets with the cotton webbing protector strips against the frame surface.
Tighten evenly
Hand-tighten each bracket so the load distributes across all four contact points.
Test before full load
Apply partial downward pressure to confirm the bar holds steady before hanging full bodyweight.
How to fit and remove the doorway bar
Check all four brackets are tightened evenly against the door frame before use.
Loosen the brackets gradually and lift the bar clear rather than letting it drop from the frame.
Keep the protector strips in the same position each time you refit the bar to avoid new contact points on the frame.
What customers say about CrossBeam
"Installation took longer than a clamp bar but it genuinely does not wobble, even mid set. Worth the extra few minutes."
Leon P.
Customer
"No marks on the door frame after a few weeks of fitting and removing it daily. The protector strips do their job."
Grace H.
Customer
"Solid bar, fit my frame fine. Grip sleeves feel firm rather than squishy which I prefer."
Tomasz K.
Customer
Frequently asked questions
Will this damage my door frame? +
The cotton webbing protector strips sit under each bracket to reduce marking, though any pressure-fit bar can leave light contact marks over time.
What door frame widths does it fit? +
The CrossBeam frame adjusts to fit standard door widths between roughly 60 and 90 centimetres.
Does it need tools to install? +
No drilling is needed; the brackets are tightened by hand to grip the door frame using the included protector strips.
Can it be removed and reinstalled often? +
Yes, it is designed to be taken down and refitted repeatedly without needing new hardware each time.